OVERLAY BRACKET KIT (FOR SOLID TOP OVERLAYS)

SKU: 1900X-2 OVERLAY KIT
$14.99

Product Name : Overlay Bracket Kit Includes: 2 ea. 2" x 2 1/8" x 2" (L*W*H) "L" Brackets
• Hole Dia. : 0.6cm / 15/64";Material : Polypropylene Plastic
• Color : Black Polypropylene Plastic with Industrial Grade Double Sided Tape Backing on One Side
• Package Content : 2 x Black Angle Brackets
• 4 x Hole Covers : And 2 x 5/8" Screws
OVERLAY BRACKETS (FOR SOLID TOP OVERLAYS) sold in Pairs Only

*FOR USE WITH EASEL DESIGN PRO'S AND FULL TABLE PRO LIGHT TABLES IF YOU WANT TO USE A SOLID TOP OVERLAY AT AN ANGLE. THIS HOOKS YOUR SOLID TOP DRAWING SURFACE TO KEEP IT FROM SLIDING. THESE ARE NOT NEEDED IF YOU ARE WORKING WITH YOUR TABLE FLAT.

INSTALL INSTRUCTIONS: PLEASE READ CAREFULLY !

This attaches to the underside of the sold top overlay (purchased seperately)  to allow your solid top drawing surface to be used with the Easel Design or Full Table Pro Lightboxes. It hooks over the back top edge of your lightbox and keeps your drawing surface from sliding down when you are working at an angle. This will be attached to the underside of your Overlay at the top back edge 8" from each side.

Adjust the angle of your Lightbox to be flat or close to flat as possible until you align your overlay and attach the Overlay Bracket Set. Once you have completed attaching the brackets to the underside of the overlay you may adjust your table top to any working angle and your solid top surface will not slide down as you work.

Simply remove your disc and place it on a flat surface in a safe location. Place your solid top overlay on to your lightbox to align the edges. You will be attaching the brackets to the underside of the overlay. So turn it over so the rubber feet are facing up so you can see them. You will attach the bracke to the same side the rubber feet are attached to.

Leave your rubber feet in place the come on the solid top overlays. The bracket will be held in place without touching your lightbox top. Made of durable Polypropylene plastic to keep from marking up your table top.

Carfully allign each bracket 8" from each side and extended out so the inside edge of the bracket is flush to the back edge of the Top - Back edge to your table top. Sit your bracket in place with the leg facing up toward you and trace the bracket on the table top with a pencil. Now you are ready to attach the brackets in place. *Remember the leg is up toward you when you attach it to the overlay because you will flip it over to use it. This will put the leg of the bracket in the downward postion when in use allowing it to "hook" the back top edge of your lightbox.

Carefully peal the backing with the printing on it without touching the sticky surface. Push in place to the tracing you made on the tabletop push it down to secure the double sided tape to hold securely. This is industrial grade double sided tape so you only get one shot at this. Once you put it in place Do Not Try To Peal it Off. It is very sticky and will not let go. This will continue to harden and be fully cured in 24 hours.

Now attach the Phillips Head Screw provided in the counter sunk -recessed hole provided in the bracket. DO NOT OVER TIGHTEN THE SCREWS. JUST SNUG IT UP TO PUSH THE BRACKET FLAT. Push on the plastic cap, yes it comes with a plastic cap to cover your screw head to keep from marking your lightbox table top just in case you remove the rubber feet on your overlay.

Now turn your solid top overlay over and allow the angled edge to extend past your lightbox top. This will "hook" the eback dge of your lightbox table top and you are ready to work. You can now adjust your lightbox to the angle you prefer and your solid top will not slide down.

When not in use your overlay solid tops may be stacked upside down so the tabs are facing up  and each top can be layered flat with the tabs at the back edge and staggered for stability.  

CALL IF YOU NEED ASSISTANCE: 951-693-5165